A Selection Guide For Used Directional Drilling Reamers
Buying new tools can be very expensive. That is why you should consider purchasing used tools if your cash is limited. Use equipment may also save you lots of money. When looking for used Directional Drilling Reamers, several factors must be considered. You should make sure that the machine is functional. Hence, you should consider the diameter, thread size, shaft as well as the style. All these will depend on the type of ground that is going to be drilled. Most contractors buy equipment that is worn out or of the wrong size. Below is a selection guide for buying pre-owned tools.
It is wise to seek the guidance of an expert before you purchase the tools. Look for an experienced professional that will offer you with the right guidance. This is because you must check if the drill pipe is operational. If the profile is damaged or worn out, look for another drilling machine that has a functional rod.
The hydraulics of the machine is also essential. Ensure that the hydraulic system pressure is within the right operating specifications. Most people overlook this step because of ignorance or because it seems insignificant. The equipment may seem operational when it is tested. However, if the pressure is low, you will experience significant problems. This will cost you time and money for the repairs. Therefore, you should ensure that you have checked the hydraulics as well.
Check the rack as well. Before you purchase the tool, make sure you have checked its rack and pinion. The carriage usually runs on the rack when it is being used. Hence, this system wears out after some time. Since there are different models, some racks will become damaged faster than others. Thus, buy a machine only after checking the tool critically.
Another critical part to check is the makeup system. This system can also be called a wrench or vice. The pipes should be screwed together when you are drilling out. It is also essential to check if the tool is working well when you are pulling back. You should test the pieces to check if they are moving as they are supposed to.
Take the time to check the reamer and drill head as well. Adapters are usually present at the tail of the housing or at the front part of the machine. This makes it easy to change the threads and use the equipment for various drill setups. Avoid tools that have adapters that have been welded in place.
The rock tooling is also critical to check before buying the used tools. Usually, the roller cones on the reamer should be tight when turning. The side to side movement will tell you whether the bearings are broken. Replacing the cones can be very costly and time-consuming.
Ensure that you are careful when looking for these tools because making a mistake will cost you dearly. Do not buy any equipment from a dealer that does not allow you to visit his shop. You should check out the shop and determine whether the dealer is reliable.
It is wise to seek the guidance of an expert before you purchase the tools. Look for an experienced professional that will offer you with the right guidance. This is because you must check if the drill pipe is operational. If the profile is damaged or worn out, look for another drilling machine that has a functional rod.
The hydraulics of the machine is also essential. Ensure that the hydraulic system pressure is within the right operating specifications. Most people overlook this step because of ignorance or because it seems insignificant. The equipment may seem operational when it is tested. However, if the pressure is low, you will experience significant problems. This will cost you time and money for the repairs. Therefore, you should ensure that you have checked the hydraulics as well.
Check the rack as well. Before you purchase the tool, make sure you have checked its rack and pinion. The carriage usually runs on the rack when it is being used. Hence, this system wears out after some time. Since there are different models, some racks will become damaged faster than others. Thus, buy a machine only after checking the tool critically.
Another critical part to check is the makeup system. This system can also be called a wrench or vice. The pipes should be screwed together when you are drilling out. It is also essential to check if the tool is working well when you are pulling back. You should test the pieces to check if they are moving as they are supposed to.
Take the time to check the reamer and drill head as well. Adapters are usually present at the tail of the housing or at the front part of the machine. This makes it easy to change the threads and use the equipment for various drill setups. Avoid tools that have adapters that have been welded in place.
The rock tooling is also critical to check before buying the used tools. Usually, the roller cones on the reamer should be tight when turning. The side to side movement will tell you whether the bearings are broken. Replacing the cones can be very costly and time-consuming.
Ensure that you are careful when looking for these tools because making a mistake will cost you dearly. Do not buy any equipment from a dealer that does not allow you to visit his shop. You should check out the shop and determine whether the dealer is reliable.
About the Author:
Find the best place to shop for directional drilling reamers by visiting our web pages today. To know more about our work history, and our rotating and hoisting equipment, view the links at http://www.pilotholebit.com .
Comments
Post a Comment